Tutorial: Easy Loose Tie-on Pants with Pockets

This tutorial will show you how to make loose tie-on pants. This is meant to be the perfect tutorial for someone who is making a pair of pants from scratch for the first time since it leaves a lot of room for mistakes. I’ll show you how to make the pattern, and then walk you through how to sew the pants step-by-step. (You can also print out the pocket pattern below, or create your own pocket for these pants)

Note: In this tutorial, I use ‘fabric’ that I created using leftover fabric scraps and remnants. If you want to learn how I did that so you can reuse your fabric scraps too, check out this tutorial.

Supplies Needed:

2 yards of fabric (You may need more depending on size and length of the pants)

Make Your Pattern:

Measurements you need:
Waist
Length of leg from waist to ankle
For the front and back pant legs:
start with a rectangle the length of your leg.
The width will be your waist measurement divided by 2 + 4inches (this allows for some overlap between the front and the back so the side of the pants doesn’t gap open.)
Front crotch seam: make a curve 12 inches down and 3 inches in from the side (don’t worry about making this curve perfect, just generally the same shape as the diagram below)
Back crotch seam: Repeat what you did for the front, but make it 5 inches from the side instead
Bottom of pants for both front and back: Move the bottom of the pants 4 inches in and connect the crotch to this for the inseam.
Make a mark 8 inches down on both the front and the back (this is a reference point that we’ll use when sewing)
For the cuff: make a rectangle that is 16 inches by 7 inches (This should work for most people, but you can make it longer if a 16 inch circumference does not fit around your foot)
For the waistband tie (you will cut 2):
Make the tie twice the length of your waist (so there is enough to tie the waistband) and 2 inches wide.
You also want to make reference marks on the waistband so that you know how far to gather the pants. The marks should be half of your waist +4 inches apart. Make sure they are centered on your waistband (see diagram below)

* The measurements I give you for the I center crotch seam are meant to make it loose so that it will fit most body types. However, if you are very tall or have a bigger bottom, you can lengthen or widen the crotch measurements for a better fit.

loose tie-on pants sewing pattern diagram

PDF pocket pattern

Step 1

hem the diagonal edge of the pockets and press the opposite two sides

Make a 1/2 inch hem on the diagonal edge of the pocket. Then press the seam allowance of the two opposite sides (the sides not touching the hem).

Step 2

sew the pocket to the side of the front pants

Line the pocket up with the top and side of the front pant pieces and edgestitch it along the two sides that you pressed under in the previous step. Baste the side that line up with the top and side of the pant leg.

Step 3

sew the front and back pant together up to the dot

with right side together, sew the outer side seam of the front and back pant pieces. Only sew from the bottom up to the dot that you made as a reference point earlier (8 inches from the top of the pants).

Step 4

narrow hem the area above the dot

Make a narrow hem on both the front and back pieces to fold over the fabric at the top 8″ of the pants and keep it from fraying.

Step 5

sew the inseam of the pant legs

fold the pants so the inseams line up and sew with right sides together.

Step 6

place one pant leg inside the other and sew the crotch seam

With right sides together, put one pant leg inside the other. Line up the crotch seam and sew it. Then turn your pants to the right side.

Step 7

add gathering stitches along the top front and back

Sew wide gathering stitches (by machine or by hand) along the top edge of the front and back pant pieces.

Step 8

gather the top of the pants

Use the marks you made on the waistband to know how far to gather your pants. The final width of each of your pant tops should be half of your waist plus 4 inches.

Step 9

sew the waistband to the pants

Center the waistband on the pant tops and sew through all layers with right sides together.

Step 10

fold the waistband in half and sew

With right sides together, fold the two sides of the waistband in half (the parts that are extended from the waistband). Then sew them.

Step 11

turn waistband to right side

Turn the waistband extensions to the right sides, these will be the ties for your pants.

Step 12

fold the waistband over and sew it to the top of the pants

Now you have the center of your waistband still flapping free. Fold it over the reverse side of the pants, encasing the gathering stitches, and topstitch through all layers.

Step 13

fold the cuffs in half and sew

With right sides together, fold the cuffs in half and sew them into a loop.

Step 14

fold the cuffs in half with wrong sides together

Fold the cuffs in half with wrong sides together.

Step 15

gather the bottom of the pant legs

Sew long gathering stitches along the bottom of both pant legs, and pull the stitches until they are the same size as the cuff.

Step 16

sew the cuff to the pants

With right sides together, sew the cuff to the pant leg.

Finished!

To wear the pants, tie the front behind you. Then tie the back of the pants around the front. Tuck the bows into the front and back pants to hide them.